8008 Epoksi TextureEpoxy Self Leveling, Orange Pattern

8008

It is an epoxy resin based, two component, solvent free, in orange peel appearance (textured), thixotropic floor covering material.

► Epoxy Resin Based
► Two Component
► Textured
► Decorative
► Anti-Slip Surface
► No Solvent

> Ral
> Public Works Pos No: 04.379/H04

• It is used in mul­ti-sto­rey and un­derg­ro­und car parks, sto­ra­ge areas, ma­in­te­nan­ce han­gars, such as pla­ces ex­po­sed to mo­de­ra­te to heavy mec­ha­ni­cal ef­fects; where re­sis­tan­ce to che­mi­cals is re­qu­ired such as che­mi­cal pro­duc­ti­on fa­ci­li­ti­es, la­bo­ra­to­ri­es; in pla­ces where aest­he­tics, easy ma­in­te­nan­ce and cle­aning are im­por­tant such as shop­ping malls, ex­hi­bi­ti­on areas, fa­irg­ro­unds and in pla­ces not ex­po­sed to sun­light. Used in­do­ors, on ho­ri­zon­tal sur­fa­ces.

• An­ti-slip fe­atu­re is inc­re­ased thanks to its te­x­tu­red sur­fa­ce.
• High mec­ha­ni­cal re­sis­tan­ce.
• High che­mi­cal re­sis­tan­ce.
• It is li­qu­id im­per­me­ab­le.
• It is aest­he­tic thanks to its wide color cho­ice and bright fi­nish.
• Long life and easy to clean.
• Sol­vent-free, eco fri­endly.

a) Surface Preparation:
The sur­fa­ce must be dry, clean, free of st­rong skate; oil, dirt or ad­he­si­on pre­ven­ti­ve ma­te­ri­als must be re­mo­ved from the sur­fa­ce; ma­te­ri­als such as mor­tar, ce­ment re­si­du­es sho­uld be sc­ra­ped. Be­fo­re appl­ying the pri­mer on the sur­fa­ce, an open po­ro­us st­ruc­tu­re sho­uld be for­med on the ce­ment top layer by using sur­fa­ce ab­ra­si­ve equ­ip­ment (Shotb­last, Ro­to­ti­ger etc). Dus­ting sho­uld be cle­aned with in­dust­ri­al va­cu­um cle­aner. The ab­ra­ded conc­re­te sur­fa­ce sho­uld have a mi­ni­mum comp­res­si­ve st­rength of 25 N/mm² and a ten­si­le st­rength of 1.5 N/mm². En­su­re that sur­fa­ce mo­is­tu­re, re­la­ti­ve hu­mi­dity and dew point re­qu­ire­ments are met be­fo­re app­li­ca­ti­on. Ot­he­r­wi­se, the de­si­red per­for­man­ce cri­te­ria can­not be re­ac­hed from the pro­duct as a re­sult of car­bo­na­ti­on re­ac­ti­on on the sur­fa­ce. Mo­is­tu­re con­tent of the sur­fa­ce sho­uld be ma­xi­mum 4%. Re­la­ti­ve hu­mi­dity sho­uld be ma­xi­mum 80%. The dew point sho­uld be above + 3°C in order to pre­vent con­den­sa­ti­on for­ma­ti­on be­fo­re and after the app­li­ca­ti­on.

b) Product Preparation:
8008 Epoksi Texture is pac­ka­ged in app­rop­ri­ate qu­an­ti­ti­es in two com­po­nents. Each com­po­nent is first mixed in it­self. Com­po­nent B (Har­de­ner) is added to com­po­nent A (Epoxy resin). It is mixed with 300 - 400 rpm mixer tip drill for 3-4 mi­nu­tes until a ho­mo­ge­no­us con­sis­tency is ob­ta­ined. The en­ti­re mi­x­tu­re is then taken to a clean con­ta­iner and mixed again. If part of the pro­duct is to be used, these mi­xing ra­ti­os sho­uld be con­si­de­red. New conc­re­te st­ruc­tu­res sho­uld be al­lo­wed to dry for a mi­ni­mum of 28 days. Repair of surface defects with a depth of more than 1 cm should be done with Termatect Epoxy Repair Mortar or Termatect Grout Mortar 6-8 hours in advance. After the surface cleaning, it should be primed with Termatect Primer in single or double layers depending on the condition of the surface in order to increase the adhesion strength and balance the surface absorbency. Depending on the porosity and structure of the surface, the surface can be leveled with the addition of filler. On surfaces that are moist up to 10%, it should be applied with Termatect Primer, otherwise the application should not be done.

c) Application Method:
8008 Epoksi Texture pre­pa­red mi­x­tu­re sho­uld be po­ured onto the sur­fa­ce and sp­re­ad with the help of a notc­hed tro­wel. It sho­uld be en­su­red that the te­x­tu­red co­ating forms a se­am­less layer on the sur­fa­ce by cros­sing it per­pen­di­cu­lar to each other with a short pile rol­ler or coral rol­ler. As an al­ter­na­ti­ve to the above app­li­ca­ti­on, 0.1 - 0.5 mm qu­artz / si­li­ca fil­ler sho­uld be added into 8008 Epoxy Te­x­tu­re to ob­ta­in a non-slip, blun­ted sur­fa­ce. Ple­ase refer to Con­sump­ti­on table for re­com­men­ded fill amo­unt.

Contact...

You can contact us to get more detailed information about our products.

“ We will continue to seek superior quality and superior service with the power we receive from you. ”

Terma Construction Chemicals
San. Tic. Ltd. Şti.